2021 Dodge Ram 1500 5.7L Engine Torque Specs| Dodge Specs (2024)

2021 Dodge Ram 1500 5.7L Complete Torque Specs List

Click the area you are looking for!

Dodge Ram 1500 5.7L HEMI Engine Repair Information

Here you can find information regarding the assembly of the Dodge 5.7L HEMI engine. In this guide we willstart from the inside of the engine including thecrankshaft, connecting rods, and piston ring installation and then move outwards all the way to the pulley beltsystem. Along the way correct procedures and torque specswill be given to aid in the assembly of the engine. Feel free to start from the beginning and work your wayoutwards or skip ahead to your current position in the engine for what you may need.

Crankshaft Main Caps Installation

The 5.7L engine block main bearing caps should be inspected for any defects or flaws before installation.Be sure to lubricate the bearing surfaces prior to installation. Once prepared you can place the caps onto the crankshaftand begin tightening the bolts down in a multi stage process. The first being 20 ft-lbs starting from the middle and going outwards.The second time around you turn each bolt an additional 90 degree turn. For the main bearing cap cross bolts you can torque them down to20 ft-lbs. Be sure togo through each bolt during each step and work your way from the inside or middle caps to the outside or outwards bearing caps.Once finished you should be good to continue with the rest of the engine.

Dodge Ram 1500 5.7L HEMI Main Cap Torque Specs : 20 ft-lbs + 90°

Dodge Ram 1500 5.7L HEMI Main Cap Cross Bolts Torque Specs : 20 ft-lbs

Piston and Connecting Rod Installation

To install the pistons and connecting rods you must first install the piston rings into each piston. Be carefulnot to stretch the rings or break them during installation. Make sure to put the correct rings in the correctpositions, this can be determined by looking atthe instructions given with the new rings. Each ring manufacturer is different so be sure to check for yourspecific rings. Once the rings have been installed you can now fit the connecting rod bearings into the end capsand lube them up with oil or lithium grease. The piston can now be lowered into the cylinder, make sure the dotor mark is facing the front of the engine and that you don't scratch the cylinder.Once installed you can match the connecting rod caps with the correct rods and start to torque the connectingrod bolts to 10 ft-lbs and then to 15 ft-lbs follwed by an additional 90 degree turn for each bolt. After all are done rotate the crankto ensure all pistons move smoothly in and out of their cylinders and nothing binds.

Dodge Ram 1500 5.7L HEMI Connecting Rod Torque Specs : 15 ft-lbs + 90°

Oil Pump Installation

When installing the oil pump be sure to use the proper sealant around the pump base if neccessary to ensure that oil pressuredoesn't drop due to leakage. Both surfaces should be cleaned and preped prior to installing. After preparing the contact surfaces carefullyinstall the oil pump onto the engine and torque down the pump mounting bolts to 20 ft-lbs. Be sure to tighten down the bolts in a cross patternto ensure that even torque is applied to the pump. From here we can install the oil pump cover and torque down its bolts to 8 ft-lbs.

Dodge Ram 1500 5.7L Oil Pump Mounting Bolt Torque Specs : 20 ft-lbs

Dodge Ram 1500 5.7L Oil Pump Cover Bolts Torque Specs : 8 ft-lbs

Dodge Ram 1500 5.7L Oil Pump Pickup Tube Torque Specs : 20 ft-lbs

Cylinder Head Installation

The first thing you must do when installing cylinder heads is to ensure both the block and head surfaces arecompletely clean from dust, oil, and any debris. The next thing you must to isto set the camshafts to their correct positions to prevent any valves from hitting pistons during installationand torquing of the head bolts. Much the same you have to set the pistons to their correctlocations, typically this means putting the #1 piston to TDC or Top Dead Center. Once everything is ready youcan install the head gasket onto the engine block by aligning the alignment dowels.Something I usually do is spray down the head gasket with some engine copper spray from permatex which you canfind here, this ensures that any gaps that could be present between the 2 surfaces gets filled with thespray. Italso helps to transfer heat between the 2 metals. With the gasket in place you can set the cylinder head ontothe gasket and block, if needed have someone assist with this process as the head can be heavyand you don't want to scratch anything or drop it! Once the head has been placed you will want to startinstalling the head bolts to make sure it doesn't move. Be sure to buy new head bolts as many manufacturersuse TTY or Torque to Yield head bolts meaning they stretch during torqueing and cannot be used twice. Also makesure to lubricate the bolts in clean engine oil before installing them into the head.Once all the head bolts have been installed and finger tightened you can start the torqueing process, almost allhead bolts have a multi-step process for torqueing. The 5.7L HEMI engine uses a single size of cylinder head bolts with a total of10 bolts being installed into the cylinder head. These head bolts should be tightened down to 25 ft-lbs and then to40 ft-lbs followed by an additional 90 degree turn. The smaller cylinder headbolts can be torqued down to 15 ft-lbs and then 25 ft-lbs also going through each bolt during each step. Make sureto now overturn or underturn any bolt as this can cause an unbalance of surface pressure between the gasket and head.

Dodge Ram 1500 5.7L HEMI Cylinder Head Main Bolts Torque Specs : 25 ft-lbs + 40 ft-lbs + 90°

Dodge Ram 1500 5.7L HEMI Cylinder Head Small Bolts Torque Specs : 15 ft-lbs + 25 ft-lbs

Timing Chain and Camshaft Installation

On the Dodge 5.7 HEMI engine the timing system is ran by the use of a single chain. This chain system consists of a sprocket on the single center located camshaftand one sprocket on the engines crankshaft. Since the camshaft is located in the center of the engine it needs to be installed from the front side of theengine. The camshaft bearings get installed using a special cam bearing installation tool. The tool simply presses the bearings in and out of the bearing holesusing different sized plates to press on them. Be sure that all of your camshaft bearings are in good condition prior to installing the camshaft and building theengine as this is a critical part of the engine. If all bearings are good and in place the camshaft can be lubed and placed into the engine. It should slideinto the bearings with ease, if it gets caught do not force it as you risk damaging the bearings. Simply move the camshaft end around until it slides in. Onceall the way into the engine you will need to install the camshaft retaining plate and its bolts. Depending on your specific Dodge engine the camshaft retainingplate gets installed immediately after the camshaft is slide into place or after the timing gear has been installed. Depening on how you took apart your engineand the new parts you are installing you will need to adapt accordingly. The retaining plate bolts need to be tightened down to 20 ft-lbs. The camshaft timingsprockets simply slide onto both the crankshaft and the camshaft end. Be sure that you install the system all together with the timing chain marks lined upwith the dots on both sprockets. Since there are no tensioners for this system it will only go together like this. On the camshaft side it aligns usinga dowel pin that sticks out of the camshaft. There is a single bolt which holds the camshaft sprocket onto the camshaft.This bolt needs to be tightened down to 90 ft-lbs. The crankshaft pulley will hold thecrankshaft sprocket in place so no need to tighten any bolts down there. Finally the timing chain has a tensioner installed on a plate which will keep thetiming chain tight during engine operation. Be sure to install the chain tensioner and torque its bolts down to 20 ft-lbs.

Dodge Ram 1500 5.7L Camshaft Sprocket Torque Spec: 90 ft-lbs

Dodge Ram 1500 5.7L Crankshaft Position Sensor Torque Spec: 8 ft-lbs

Dodge Ram 1500 5.7L Camshaft Retaining Plate Bolts Torque Spec : 20 ft-lbs

Dodge Ram 1500 5.7L Camshaft Timing Chain Tensioner Torque Spec : 20 ft-lbs

Dodge Ram 1500 5.7L Rocker Arms Torque Spec : 15 ft-lbs

Dodge Ram 1500 5.7L Valve Lifter Retainer Torque Spec : 8 ft-lbs

Timing Cover Installation

The timing cover on the 5.7L is used to cover up the internals of the engine and hold in massive amounts of oil. For this reason I recommend usingsome silicon sealant along with a new gasket during installation. Be sure to clean all of the metal surfaces prior to installation and placing the silicon onto the metal.With everything ready to install be sure to double check your timing and engine internals before placing the cover in place. Another tip is to lube up thecrankshaft seal with some oil so it seats better. If everything is good to go then place the coveronto the engine block and begin to tighten down the bolts hand tight. Once all of the bolts have been set in place be sure to follow your sealants instructions by waiting the recommendedtime. Once ready you can torque down the timing cover bolts to 40 ft-lbs going in a cross pattern.

Dodge Ram 1500 5.7L Timing Cover Bolts Torque Specs : 40 ft-lbs

Oil Pan Installation

Much like the timing cover on the 5.7L the oil pan plays an important role in keeping the engine oil inside theengine. For this reason I recommend using a new gasket as well as some silicone sealantduring installation. Using the same technique as before with the cover you clean the surfaces of both the oilpan and the engine block and then install the new gasket onto the block and then followit up with some silicone sealant. Be sure to follow your sealants instructions to ensure you get the best sealfrom your application. The oil pan bolts can be torqued down to 10 ft-lbs following a cross pattern.Along with the pan is the oil pan drain plug, this gets removed and reinstalled quite frequently and can betorqued down to 25 ft-lbs.

Dodge Ram 1500 5.7L Oil Pan Torque Specs : 10 ft-lbs

Dodge Ram 1500 5.7L Oil Drain Plug Torque Specs : 25 ft-lbs

Valve Covers Installation

The valve cover installation is rather simple, there are rubber seals for each bolt hole and a silicone gasketthat prevents oil from leaking out of the engine. It is recommended to replace both the sealsand the gaskets although if they are in good condition you can reuse them. If you do choose to reuse them Iwould use some silicone sealant along with the silicon gasket to ensure it does not leak.The valve cover bolts torque down to 106 in-lbs or about 8 ft-lbs in a criss cross order. Be sure not to missany bolts to avoid having oil leak out onto the exhaust pipes and cause a lot of smoking.

Dodge Ram 1500 5.7L Valve Cover Torque Specs : 8 ft-lbs

Intake Manifold and Fuel Rail Installation

When installing the intake manifold you want to make sure you have all the surfaces as well as intake holescleaned out before placing the manifold into position. Once cleaned you can then placethe intake manifold gaskets onto the alignment pins. If you want you can also use a little bit of sealant on thegaskets to help ensure there are no leaks. With the gaskets in place you can now putthe manifold down onto the gaskets and begin to install the bolts. The intake manifold bolts torque to 10 ft-lbsand can be tightened in a cross pattern. The ignition coil assembly can be torque down to 8 ft-lbs and the spark plugs themselves can betorqued down to 13 ft-lbs, be careful not to overtorque these as they can snap and cause big problems.When installing the throttle body make sure that all of the gaskets are in good condition and will hold a seal as you do notwant to be leaking gas fumes around the engine. If everything looks good you can tighten the throttle body bolts down to 8 ft-lbs.

Dodge Ram 1500 5.7L Intake Manifold Torque Specs : 10 ft-lbs

Dodge Ram 1500 5.7L Ignition Coil Assembly Torque Spec : 8 ft-lbs

Dodge Ram 1500 5.7L Spark Plug Torque Specs : 13 ft-lbs

Dodge Ram 1500 5.7L Throttle Body Torque Specs : 8 ft-lbs

Exhaust Manifold Installation

The exhaust manifold can be installed by cleaning the surface areas on both the head an the manifold itself andthen by using the exhaust manifold gasket and putting it in place. Once the gasket is in itslocation you can put the manifold onto the heads and begin to torque them down to 18 ft-lbs. I always use somecopper spray from permatex on the exhaust manifold gaskets to ensure I do not end up withany exhaust leaks once done. When you go to install the engine into the vehicle or if it is already in thevehicle the torque specs for the exhaust manifold to the exhaust pipes or catalytic converter is 25 ft-lbs.

Dodge Ram 1500 5.7L Exhaust Manifold Torque Spec : 18 ft-lbs

Dodge Ram 1500 5.7L Exhaust Pipe Torque Specs : 25 ft-lbs

Water Pump and Thermostat Installation

The water pump on the Dodge 5.7L engine gets tightened down to the engine block on the serpentine belt side and is ran off of thedrive belt. When removing the old water pump be sure that you drain out the coolant prior to removal otherwise the coolant will spill all over.Once drained you can remove the water pump mounting bolts and remove the old pump from the vehicle. From here we can clean up the engine blocksmating surface and prepare the new water pump for installation. Be sure to use a new gasket and some silicon sealant to ensure that no coolantends up leaking and causes further engine damage down the road. Once prepared you can install the pump onto the engine and hand tighten the bolts down.Once all of the bolts have been installed you can then torque down the bolts to 20 ft-lbs. Make sure to follow your sealants instructions as they oftenrequire you to wait an extended amount of time before torqueing down the bolts. From here you can install the water pump pulley and fan and torque them downto 19 ft-lbs.

Dodge Ram 1500 5.7L Water Pump to Case Torque Specs : 20 ft-lbs

Dodge Ram 1500 5.7L Water Pump Pulley Torque Specs : 19 ft-lbs

Front Dress and Pulley belt Installation

Most of what is left on the engine is just place and tighten objects such as the belt pulleys, belt tensioner,throttle body, oil filter neck, crankshaft pulley, and motor mounts. If the items have a gasket and hold eitheroil or coolant inside the engine then feel free to add some sealant along with the gasket. Always be sure toinspect your gaskets and replace them if there is any deteriation or flaws with them. For thebelt system the crankshaft pulley gets tightened down to the crankshaft at 130 ft-lbs.The drive belt tensioner can be tightened to 33 ft-lbs and the idler pulley can be torqued down to 16 ft-lbs. When installing be sure theyboth turn smoothly and if they do not then replace them with new ones as the bearings can go bad. The enginemotor mount can be installed onto the engine block if it hasn't been already, the torques forthe mount to the block is 59 ft-lbs and then when installing the mount to the vehicle or frame it can be torqued to35 ft-lbs. Finally the throttle body can be installed on top of the intake manifoldwith a good gasket and some added sealant using 7 ft-lbs in a criss cross pattern. For installing the belt youcan use a tool to move the tensioner into its springed state and install the belt as shown in thepicture. The generator or alternator can be tightened down to the engine block using 40 ft-lbs of force.The power steering pump can be installed and torqued down to 18 ft-lbs and finally the A/C compressor can be torqued down to15 ft-lbs of force.

Dodge Ram 1500 5.7L Crankshaft Pulley Torque Specs : 130 ft-lbs

Dodge Ram 1500 5.7L Idler Pulley Bolt Torque Spec : 16 ft-lbs

Dodge Ram 1500 5.7L Drive Belt Tensioner Torque Specs : 33 ft-lbs

Dodge Ram 1500 5.7L Motor Mount to Engine Torque Specs : 59 ft-lbs

Dodge Ram 1500 5.7L Motor Mount to Frame Torque Specs : 35 ft-lbs

Dodge Ram 1500 5.7L Alternator to Block Torque Specs : 40 ft-lbs

Dodge Ram 1500 5.7L Power Steering Pulley Torque Specs : 18 ft-lbs

Dodge Ram 1500 5.7L A/C Compressor to Block Torque Specs : 15 ft-lbs